09982 Magnetic Deep Fryer Power Cord for Presto
4.5Editor score
Replaces 09982 9982 85691
Supports listed Presto fryer models
Flexible twenty-eight-inch cord
In this guide
A magnetic power cord gives many electric deep fryers a safer, more convenient way to connect to a wall outlet. The right replacement must match both the fryer’s model and connector dimensions, while also meeting the appliance’s voltage, amperage, wire-gauge, and certification requirements. Compatibility matters more than a similar appearance.
This guide compares 10 magnetic cord replacements for Presto, Masterbuilt, Hamilton Beach, T-Fal, Secura, Farberware, Butterball, Secura, and other electric fryers. The comparison considers supported model numbers, connector type, electrical ratings, cord length, material details, and break-away behavior rather than treating every magnetic cord as interchangeable.
Each review explains the strongest reasons to consider a particular cord, along with fit limitations and safety considerations. The top picks highlight a versatile aftermarket option, a well-rated Presto replacement, and a focused Masterbuilt cord. Product listings and prices can change, so shoppers should verify the current details and their fryer model before ordering.
Top 3 Picks for Best Deep Fryer Magnetic Power Cord Replacement
Deep Fryer Cord Compatible with Hamilton Beach & Masterbuild
4.6Editor score
Broad multi-brand model compatibility
ETL-certified 125V 15A design
Four-point-five-six-foot pure copper cable
9001150010 Break-Away Magnet Power Cord for Masterbuilt
5.0Editor score
Targeted Masterbuilt 10L XL fit
All-copper 18AWG power conductor
Heat-resistant break-away cable
Top 10 Best Deep Fryer Magnetic Power Cord Replacement in 2026 Compared
The comparison below places each replacement cord side by side, focusing on model fit, connector design, electrical specifications, and practical compatibility. Because magnetic connectors can look similar while having different dimensions, the listed model numbers and physical measurements remain the most important buying considerations.
ProductsSpecificationsEditor scorePrice
Best Budget
09982 Cord for Presto
Presto 120V 15A
Twenty-eight-point-five inch cord
Thick copper core
Heat-resistant outer jacket
3.8Editor score
Editor's Choice
Cord for Hamilton Beach and Masterbuild
Multi-brand fryer compatibility
ETL-certified 125V 15A
Sixteen AWG pure copper
Four-point-five-six-foot cable
4.6Editor score
Best Premium
T-Fal FF103850 Magnetic Cord
T-Fal model-specific fit
120V 15A electrical rating
Three-quarter-inch hole spacing
One-and-one-half-inch plug width
4.3Editor score
09982 Cord for Presto
Presto 120V 15A
Twenty-eight-point-five inch cord
Direct OEM-style replacement
Flexible two-prong design
4.5Editor score
Masterbuild Break-Away Cord
Masterbuild 10L XL fit
ETL-certified 125V 15A
Three-point-two-eight-foot cord
Full copper three-pin connector
5.0Editor score
09982 Cord for Presto
Presto 120V 15A
Thick copper conductor
One-hundred-five-degree jacket
Tool-free magnetic connection
4.1Editor score
VASTHOME Five-Foot Fryer Cord
Sixteen AWG pure copper
ETL-certified 125V 15A
Five-foot flat cable
Two-pin wall connector
4.2Editor score
Secura L-DF401B-T Cord
Secura model-specific fit
One-meter cord length
Point-five by one-point-six port
Break-away magnetic connection
4.1Editor score
9001150010 Masterbuild Cord
Masterbuild 10L XL fit
All-copper 18AWG conductor
Three-point-two-eight-foot cable
Heat-resistant protective housing
5.0Editor score
09982 Cord for FryDaddy
FryDaddy and GranPappy fit
Presto 120V 15A
Twenty-eight-point-five inch cord
Magnetic appliance connector
3.8Editor score
1. 09982 Cord for Presto – Comprehensive Presto Compatibility
09982 Cord for Presto
Presto 120V 15A
Twenty-eight-point-five inch cord
Thick copper conductor
Flame-retardant outer jacket
This 09982 replacement targets Presto FryDaddy and other compatible electric deep fryers, with a customer rating of 3.8. Its primary appeal is model coverage: the listing identifies 15 Presto model numbers, including examples from the 0541106, 0542008, 0544000, 0545000, and 0546000 series. That breadth makes it worth checking when the model number on a fryer appears anywhere in the supported list.
Pros
- Extensive listed Presto support
- Thick copper core
- Tool-free magnetic attachment
- Heat-resistant outer jacket
- Works across multiple settings
Cons
- Lowest customer rating listed
- Compatibility is brand-specific
We may earn a commission when you buy through this link, at no additional cost to you.
The cord uses a thicker copper core and a flame-retardant jacket described as resistant to temperatures up to 105°C. A magnetic appliance connector allows it to attach at the touch of a button, while the installation description says replacement can be completed in three seconds without tools. The design is also marketed for home kitchens, outdoor camping, and catering events, although suitability still depends on the fryer, outlet, cord, and operating environment.
The main drawback is its 3.8 rating, the lowest among the listed products. Buyers should therefore pay especially close attention to the model number and connector rather than relying on the broad Presto association. A magnetic connection is also designed to detach readily, so the fryer should not be moved while operating. The cord should be disconnected from the wall before being reattached or inspected.
This cord is a practical choice for a Presto owner whose model appears in the published compatibility list and whose original cable is cracked, damaged, or no longer holds a secure connection. It is less suitable for someone who cannot verify the fryer model or wants a product with a stronger customer rating. For the correct listed model, its quick attachment, copper core, and heat-resistant jacket provide solid replacement fundamentals.
Broad Presto Model Support
The extensive list of supported Presto models gives this replacement a useful advantage over cords tied to a single fryer family. Check the number printed on the appliance against the published list before buying, since a shared brand name alone does not establish connector compatibility.
Fast Magnetic Attachment
The magnetic interface removes the need to align and force a conventional plug into the fryer. It also detaches readily, so the connection should never be treated as a way to reposition the appliance while it is powered or heating.
We may earn a commission when you buy through this link, at no additional cost to you.
2. Cord for Hamilton Beach and Masterbuild – Broadest Multi-Brand Support
Cord for Hamilton Beach and Masterbuild
Multi-brand fryer compatibility
ETL-certified 125V 15A
Sixteen AWG pure copper
Four-point-five-six-foot cable
This aftermarket magnetic cord combines a strong 4.6 customer rating with compatibility across several widely recognized fryer brands. The listing names Hamilton Beach 35032, 350354, 35034, and 12 Cup models, along with Secura TSAF40DH and MSAF40DH, Farberware WM 16116, Pukomc MM25CY, and some Masterbuilt fryers. It stands out as the most convincing all-brand option in this roundup.
Pros
- Strong customer rating
- Works across several brands
- ETL-certified electrical design
- Pure copper sixteen AWG cable
- Convenient four-point-five-six-foot length
Cons
- Requires model and plug verification
- Not universal across all fryers
We may earn a commission when you buy through this link, at no additional cost to you.
Its electrical specification is 125V and 15A, and the product is described as ETL certified. The cable is a 4.56-foot, or 54.7-inch, flat lead made from 16 AWG pure copper and fitted with an ETL-certified two-pin plug. Heat-resistant materials are intended to support reliable operation, while the relatively long cord offers more placement flexibility than the 28.5-inch Presto-specific alternatives.
Compatibility still needs to be confirmed against the appliance. The seller specifically advises checking the fryer model and plug shape before purchase, which is important because magnetic connectors can appear interchangeable even when their spacing or dimensions differ. The break-away construction also means accidental contact can stop heating, so the fryer should remain stationary and the wall plug should be removed before reconnecting the magnetic end.
This is the strongest all-around recommendation for a shopper who owns one of the named Hamilton Beach, Secura, Farberware, or Pukomc models and wants a cord with a high rating and certified construction. It also works for some Masterbuilt fryers, provided the physical connector and listed model match. It is less appropriate for an unidentified fryer or for anyone unwilling to compare model numbers and port dimensions.
Useful Cross-Brand Compatibility
Few options in this guide list as many brands and models as this replacement. That makes it a useful first candidate for popular fryers, but the explicit compatibility list should still be treated as the final authority rather than assuming every model from a named brand will fit.
Certified Pure Copper Construction
The stated 16 AWG pure copper conductor, 125V/15A rating, and ETL certification provide a clearer specification profile than many competing listings. Those details make the cord suitable for matching fryers that require a two-pin appliance connection.
We may earn a commission when you buy through this link, at no additional cost to you.
3. T-Fal FF103850 Magnetic Cord – Precise Model-Specific Fit
T-Fal FF103850 Magnetic Cord
T-Fal model-specific fit
120V 15A electrical rating
Three-quarter-inch hole spacing
One-and-one-half-inch plug width
This T-Fal SS-992896 replacement is designed around the FF103850/89 platform and carries a 4.3 customer rating. Unlike broad cross-brand cords, it gives unusually precise physical measurements, including 3/4-inch spacing between the two holes, 1/4-inch spacing between the metal magnets, a 1 1/2-inch overall plug width, and a 7/8-inch overall height. Those measurements help validate fit beyond the model number alone.
Pros
- Detailed connector measurements
- Long list of compatible models
- Clearly stated electrical rating
- Purpose-built T-Fal replacement
- Precise fit guidance
Cons
- Cannot fit unlisted models
- Limited brand coverage
We may earn a commission when you buy through this link, at no additional cost to you.
The cord is rated for 120 volts and 15 amps and is intended for a defined selection of T-Fal fryers. The title includes FF103850/89, while the compatibility details also list FF103850/87, FF122851/87A, FF162850/87A, FF172D52/87A, several FR404 models, FR702D50/87, FR702D50/89, FR702D51/87, FR800050/87A, and FR804050/87A. A buyer should check the appliance label carefully because the seller states that an unlisted model will not fit.
The trade-off is narrow compatibility. A shopper with a T-Fal fryer outside the list may need another option, and similar-looking aftermarket plugs cannot safely be assumed to work. The benefit of this more focused design is that its dimensions and supported models provide useful confirmation when the original connector has been lost or the fryer is no longer in its original condition.
This is a strong choice for a T-Fal owner who can match the exact model and connector measurements. It avoids the uncertainty of a universal-looking cable and provides a clearly defined replacement for the listed fryer range. It should not be selected merely because the fryer carries the T-Fal name; compatibility must be confirmed from the model and the listed measurements.
Measurements That Confirm Fit
The stated hole spacing, magnet spacing, plug width, and height are unusually valuable when confirming a purchase. Measure the existing fryer port or compare it with the removed connector before ordering, because the seller explicitly excludes unlisted models.
A Focused T-Fal Solution
Model-specific replacement cords reduce the risk of choosing a visually similar connector. They are especially helpful for owners who can identify the exact appliance and know that the original magnetic lead has reached the end of its service life.
We may earn a commission when you buy through this link, at no additional cost to you.
4. 09982 Cord for Presto – Balanced Presto Replacement
09982 Cord for Presto
Presto 120V 15A
Twenty-eight-point-five inch cord
Replaces three part numbers
Magnetic two-prong design
This 09982 magnetic cord earns a 4.5 rating and offers a balanced replacement for Presto FryDaddy, GranPappy, and compatible electric fryers. It directly replaces part numbers 09982, 9982, and 85691, making it particularly helpful for owners who recognize one of those numbers from the original cord. The product also identifies 15 compatible Presto models, spanning several 054-series fryers.
Pros
- Well-regarded customer rating
- Replaces three common part numbers
- Wide listed Presto compatibility
- Flexible twenty-eight-inch cable
- Clear voltage and amperage specification
Cons
- Short cord length
- Limited to supported Presto models
We may earn a commission when you buy through this link, at no additional cost to you.
Its electrical rating is 120V and 15A. The cord measures 28.5 inches, with a magnetic connector at the appliance end and a standard two-prong plug at the other. High-quality raw materials are described as producing a sturdy, flexible cable that resists cracking and damage. That combination of a clear part-number cross-reference, defined dimensions, and a strong rating makes this one of the clearer listings in the group.
The main limitation is length. At 28.5 inches, it is shorter than the 4.56-foot and five-foot alternatives, which may restrict countertop placement when the wall outlet is not directly beside the fryer. It is also not a general-purpose cable: the compatibility claims center on Presto models, so the appliance number and connector must be verified before purchase.
This is the most balanced pick for a Presto owner seeking a well-rated, clearly identified replacement without paying for the broader compatibility claims of a multi-brand cord. It suits users whose original part number is 09982, 9982, or 85691 and whose outlet can be reached comfortably with a 28.5-inch lead. Verify the listed fryer model, then consider the available counter space before ordering.
Three Recognized Part Numbers
Replacing 09982, 9982, and 85691 gives owners multiple ways to identify the correct original component. Finding one of those markings on the old cord or fryer documentation can make the purchase decision much easier.
Compact and Flexible Layout
The 28.5-inch lead is easy to route behind a fryer and offers less clutter than a longer cord. It is a practical choice when the outlet is close, while longer alternatives may be more convenient for a wider countertop arrangement.
We may earn a commission when you buy through this link, at no additional cost to you.
5. Masterbuild Break-Away Cord – Broad Fryer Compatibility
Masterbuild Break-Away Cord
Masterbuild 10L XL fit
ETL-certified 125V 15A
Three-point-two-eight-foot cord
Full copper three-pin plug
This break-away magnetic cord has a 5.0 customer rating and presents one of the broadest compatibility claims in the guide. It is specifically designed for the Masterbuild 10 Liter XL Electric Fryer, including models MB20012420 and MB20010326, but it also lists Presto, Hamilton Beach, Farberware WM 16116, and Pukomc MM25CY compatibility. That makes it a potential one-cord solution for households owning more than one supported fryer.
Pros
- Perfect five-point-zero rating
- Covers several major fryer brands
- ETL-certified 125V 15A design
- Full copper wire core
- Explicit break-away safety guidance
Cons
- Compatibility excludes Farberware 510649
- Connection can separate accidentally
We may earn a commission when you buy through this link, at no additional cost to you.
The cord is ETL certified, rated at 125V and 15A, and measures 3.28 feet. It uses an 18 AWG full copper core and a three-pin plug. The insulation and cable are described as heat resistant, with the intention of improving reliability and extending the service life of a fryer whose original cord has worn out. The magnetic connection is easy to adsorb and release, and the product guidance stresses checking for metal objects and confirming a complete connection before use.
There is one explicit incompatibility: the listing says it does not fit Farberware deep fryer 510649. More broadly, compatibility claims for many brands should still be checked against the exact model, particularly because a three-pin configuration will not suit a fryer designed around a two-pin connection. The break-away design also has a built-in operational tradeoff, since accidental contact can interrupt heating.
This cord is an attractive pick for a Masterbuilt 10L XL owner who values the perfect listed rating, ETL certification, and the possibility of using it with other supported fryers. It is also useful for a household that wants a spare compatible cord. Shoppers should verify their fryer against the full list, particularly for Farberware models, and must unplug the wall end before attempting to reconnect a separated magnetic plug.
One Cord, Multiple Supported Fryers
The unusually broad brand coverage can simplify replacement for a household with more than one supported appliance. Each model should still be checked because the same brand name can encompass connectors with different pin arrangements and dimensions.
Purpose-Built Break-Away Design
The magnetic coupling is designed to release when pulled, which can help limit movement or spills caused by a tug. It also means the connection can separate unexpectedly, so the fryer should remain still and the cord should be inspected before every use.
We may earn a commission when you buy through this link, at no additional cost to you.
6. 09982 Cord for Presto – Durable Heat-Resistant Design
09982 Cord for Presto
Presto 120V 15A
Thick copper conductor
One-hundred-five-degree jacket
Tool-free magnetic attachment
This Presto replacement has a 4.1 customer rating and emphasizes a durable copper core and heat-resistant jacket. Its compatibility list covers numerous 054-series Presto fryers, including 0541106, 0542008, 0542221, 0542408, 0542508, 0544206, 0544306, 0544405, 0544505, 0545002, 0545102, 0545202, and 0546002. It also identifies 09982, 9982, and 85691 as replacement references.
Pros
- Supports numerous Presto models
- Heat-resistant flame-retardant jacket
- Thick copper power core
- Easy detachment and reattachment
- Clear household electrical rating
Cons
- Moderate customer rating
- Limited Presto-focused compatibility
We may earn a commission when you buy through this link, at no additional cost to you.
The jacket is described as flame retardant and resistant to temperatures up to 105°C. At 120V and 15A, the cord is intended for household Presto fryers that use a conventional 120-volt outlet, with no converter stated as necessary. A magnetic interface makes the appliance end easy to detach and reattach, avoiding the repeated alignment and strain associated with a conventional plug.
Its 4.1 rating is solid but not as strong as the leading options, and the 105°C jacket figure should not be mistaken for a statement that the entire cord can be immersed, exposed to flame, or left against a hot fryer. Heat resistance and safe operating clearance are different considerations. The magnetic coupling can also separate if touched, making careful placement important during a cooking cycle.
This is a sensible option for a Presto user who values a thick copper core and a heat-retardant jacket over a longer cord. It is particularly relevant for a FryDaddy or GranPappy whose original magnetic lead is damaged and whose model number appears in the supplied list. Buyers should avoid choosing it for an unidentified appliance or for another brand simply because its connector resembles a Presto fitting.
Heat-Retardant Outer Jacket
A jacket described as flame retardant and resistant up to 105°C is a useful feature in a heated countertop environment. It does not eliminate the need to keep the cord clear of hot surfaces, oil, and moving parts.
Presto Part-Number Cross-Reference
The references to 09982, 9982, and 85691 help owners identify a direct replacement rather than relying only on a generic product description. Finding the original part number can also make it easier to confirm the appliance connection before ordering.
We may earn a commission when you buy through this link, at no additional cost to you.
7. VASTHOME Five-Foot Fryer Cord – Flexible Multi-Brand Replacement
VASTHOME Five-Foot Fryer Cord
Sixteen AWG pure copper
ETL-certified 125V 15A
Five-foot flat cable
Two-pin wall connector
The VASTHOME replacement stands out for its five-foot length and broad list of supported electric fryers. Its 4.2 customer rating is complemented by compatibility claims covering Hamilton Beach 35032, 350354, 35034, and 12 Cup models; Butterball Turkey, XL, and XXL fryers; Masterbuilt turkey fryers; Secura TSAF40DH and MSAF40DH; Farberware WM 16116; and Pukomc MM25CY.
Pros
- Generous five-foot cable length
- Supports numerous named brands
- Sixteen AWG pure copper construction
- ETL-certified 125V 15A design
- Includes warranty and support
Cons
- Not compatible with several fryer brands
- Does not fit Farberware 510649
We may earn a commission when you buy through this link, at no additional cost to you.
The cable is a 16 AWG pure copper flat lead measuring five feet, or 60 inches. It is described as lightweight, ETL certified, and rated for 125V and 15A, with a two-pin wall plug. The flat construction may be easier to route along a counter, while the longer lead gives more freedom between the fryer and outlet. The seller also states that the connector should be checked against the appliance port before use.
The exclusions are significant: the product is not compatible with Seneca, Breakaway, Waring, or Oster deep fryers, and it does not fit Farberware 510649. Those limitations are useful because they show why a brand name alone should never be used as a compatibility test. Accidental contact can also disengage the magnetic connection, and the guidance specifically says to unplug the wall end before reconnecting.
This is a good choice when a longer lead is needed, especially for a Butterball or a named Hamilton Beach, Masterbuilt, Secura, Farberware, or Pukomc model. Its certified 16 AWG construction and 18-month warranty add confidence, but the buyer must accept the brand exclusions and verify the exact fryer. It is not the right option for a Seneca, Breakaway, Waring, Oster, or Farberware 510649 appliance.
Room for Flexible Countertop Placement
The five-foot cable is the longest option in this group and can reduce the need to place the fryer immediately beside an outlet. It is useful when countertop depth or outlet location would make a shorter lead inconvenient.
Compatibility Includes Clear Exclusions
The stated support for several popular brands is balanced by explicit non-compatibility with Seneca, Breakaway, Waring, Oster, and Farberware 510649. These exclusions make it easier to avoid a mismatched purchase, provided the exact model is still checked.
We may earn a commission when you buy through this link, at no additional cost to you.
8. Secura L-DF401B-T Cord – Precise Secura Port Fit
Secura L-DF401B-T Cord
Secura model-specific fit
One-meter cord length
Point-five by one-point-six port
Break-away magnetic connector
This Secura magnet cord is built specifically for the L-DF401B-T and DF-03 deep fryers. It has a 4.1 customer rating and measures one meter in length. The product information gives the fryer connection port as 0.5 by 1.6 inches, making physical verification possible before purchase. It is a deliberately narrow replacement rather than a general multi-brand cord.
Pros
- Exact Secura model guidance
- Published port dimensions
- Simple one-meter length
- Purpose-made magnetic replacement
- Clear warning against universal use
Cons
- Compatible with very few models
- Connection may fail when mismatched
We may earn a commission when you buy through this link, at no additional cost to you.
Its magnetic break-away connection is required by the safety guidance cited in the listing, and the cord should never allow a fryer to be moved while in use. The seller notes that connection failure may result from using the wrong brand or model, which is why repeated emphasis is placed on checking the port size and confirming that the appliance is an L-DF401B-T or DF-03. The result is a straightforward replacement for owners who know they have one of those models.
The limited compatibility is the defining trade-off. This cord will not serve as a universal Secura, Masterbuilt, Hamilton Beach, or Presto replacement, and a visually similar connector may not engage correctly. It is also important not to force a connector that appears close but does not meet the stated dimensions. For anyone uncertain about the fryer model, a broader replacement with a detailed compatibility list may be easier to evaluate.
This cord is recommended for a Secura owner who can positively identify the L-DF401B-T or DF-03 model and measure the port. It offers a straightforward, model-specific solution with a one-meter lead and magnetic disconnection. It is unsuitable for other fryer brands, and buyers should contact the seller or consult the appliance documentation if the model designation is not visible.
Exact Port Dimensions
The stated 0.5-by-1.6-inch connection dimensions allow a buyer to check the fryer before ordering. This is more reliable than comparing photographs, especially when multiple manufacturers use similar magnetic connector shapes.
Deliberately Restricted Compatibility
Restricting the cord to two Secura models reduces the risk that it will be treated as a universal solution. It also means that a Secura fryer outside the specified range requires another replacement, even if the port appears similar.
We may earn a commission when you buy through this link, at no additional cost to you.
9. 9001150010 Masterbuild Cord – Refined Masterbuild Safety Design
9001150010 Masterbuild Cord
Masterbuild 10L XL fit
All-copper 18AWG conductor
Three-point-two-eight-foot cable
Heat-resistant protective housing
This 9001150010 break-away magnetic cord holds a 5.0 customer rating and is built around two Masterbuilt 10L XL electric fryer models, MB20012420 and MB20010326. It is a focused replacement for owners who can match that exact part number, with a design that centers on a clean, tool-free connection and deliberate magnetic disengagement.
Pros
- Perfect five-point-zero rating
- Exact replacement part number
- Masterbuilt-specific model support
- All-copper 18AWG conductor
- Break-away safety mechanism
Cons
- Focused on two Masterbuilt models
- Anti-interference claim lacks certification detail
We may earn a commission when you buy through this link, at no additional cost to you.
The electrical specification is 125V and 15A, with an 18 AWG all-copper core and a 3.28-foot cable. The conductor is described as high-purity copper, while the cable and housing use heat-resistant, flame-retardant, and wear-resistant materials. The plug-and-play design does not require precise alignment, allowing users to connect or remove the cord while holding the plug and reducing the chance of damaging the appliance connector.
Some performance language in the listing goes beyond basic compatibility and electrical data. Claims about overload protection, anti-interference performance, and stable voltage output are not accompanied by the same level of certification detail found in specifications such as the Masterbuild 10L XL fit. Shoppers should judge the cord by the verified model match, conductor size, rating, and construction, rather than assuming that every listed performance claim has independent documentation.
This is the premium-focused pick for a Masterbuilt owner seeking a purpose-matched replacement with a perfect customer rating. It is especially compelling when the old cord is worn, cracked, or prone to disconnecting and the fryer is one of the two clearly named models. It is not a general-purpose option for other brands, and the magnetic break-away behavior means the appliance should never be moved while connected to power.
Purpose-Built Electrical Details
The all-copper 18 AWG conductor, 125V/15A rating, and 3.28-foot length provide concrete details for Masterbuilt buyers. These specifications align closely with other cords designed for the same 10L XL class of appliance.
Deliberate Safety Disconnection
The magnetic coupling is intended to detach quickly when tugged, potentially reducing the likelihood of dragging or tipping the fryer. It must never be used to move the appliance, and the fryer should remain stable for the entire cooking cycle.
We may earn a commission when you buy through this link, at no additional cost to you.
10. 09982 Cord for FryDaddy – Simple Presto-Style Replacement
09982 Cord for FryDaddy
FryDaddy and GranPappy fit
Presto 120V 15A
Twenty-eight-point-five inch cord
Magnetic appliance connector
This 09982 magnetic cord is aimed at FryDaddy, GranPappy, and compatible Presto deep fryers, and it carries a 3.8 customer rating. It supports a long list of 054-series model numbers, including 0541106, 0542008, 0542221, 0542408, 0542508, 0544206, 0544306, 0544405, 0544505, 0545002, 0545102, 0545202, and 0546002. Part numbers 09982, 9982, and 85691 provide useful original-part references.
Pros
- Recognized 09982 replacement
- Supports major Presto model numbers
- Matches listed 120V 15A requirements
- Heat-resistant cable materials
- Simple magnetic appliance connection
Cons
- Tied to the lowest listed rating
- Short cord and limited compatibility
We may earn a commission when you buy through this link, at no additional cost to you.
The cord is rated for 120V and 15A and measures 28.5 inches. A magnetic plug connects to the fryer, while the opposite end uses a two-hole wall plug. The cable is described as thick, black, heat resistant, and intended for long-lasting use. Those characteristics suit a countertop Presto appliance that has experienced normal heat exposure and cable movement over time.
The product shares the lowest customer rating in the comparison, which gives careful buyers a reason to compare the other Presto-specific options. Its shorter lead may also be less convenient than the 3.28-foot, 4.56-foot, and five-foot choices. As with all magnetic break-away cords, the connection should be checked for metal objects and kept away from children, and the fryer should not be moved while connected.
This is a straightforward replacement for someone who has confirmed one of the supported FryDaddy, GranPappy, or Presto models and needs the recognized 09982-style connection. It is best considered alongside the other 09982 options because their compatibility, ratings, and stated construction differ. If the model number is unknown, a cross-brand cord with a more detailed published fit list may be a safer place to start.
Recognized Presto-Style Connection
The 09982, 9982, and 85691 references allow an owner to match the cord against an existing part number. This reduces ambiguity when replacing a visibly worn cable, although the fryer model and connector still need confirmation.
Compact Heat-Resistant Construction
The 28.5-inch heat-resistant cable is compact enough for close countertop placement. It should still be routed away from hot surfaces, grease, and the fryer basket, since material resistance does not remove the need for sensible separation.
We may earn a commission when you buy through this link, at no additional cost to you.
Buying Guide – How to Choose the Best Deep Fryer Magnetic Power Cord Replacement
A magnetic fryer cord is only suitable when its model compatibility, connector geometry, electrical specifications, and safety behavior align with the appliance. The most important first step is to identify the fryer, then use those requirements to narrow the replacement options.
Fryer Model Compatibility
Begin with the complete model number rather than the brand name alone. Presto, Masterbuild, Hamilton Beach, Secura, and other manufacturers use several fryer families, and a cord listed for one model may not engage with another. Compare the appliance number with every entry in the replacement listing, including any stated exclusions. If the fryer model cannot be found, do not assume the closest numerical or visual match is compatible.
In short, confirm the exact fryer model and its listed compatibility before ordering.
Connector Geometry
Magnetic connectors can have different hole spacing, magnet spacing, widths, heights, and pin arrangements. The T-Fal replacement illustrates the value of published measurements, while the Secura cord gives an exact port size. Measure the existing port or removed plug when possible, and compare both dimensions and pin count rather than relying on a photograph. A connector that looks right but does not match the appliance port should not be forced.
In short, match connector dimensions and pin configuration, not appearance alone.
Voltage and Amperage
The replacement must meet the fryer’s electrical requirements. Most options in this guide are listed for 120V or 125V and 15A, but the voltage distinction still matters: 125V describes the cord’s rating, while the appliance should be designed for a standard household supply. Confirm the rating on the fryer and on the original cord, and avoid using a lower-rated or under-specified replacement merely because the magnetic end appears to fit.
In short, use the fryer and cord ratings to confirm electrical suitability.
Wire Gauge and Conductor
Wire gauge helps indicate how much current the cable is designed to carry, while copper construction can support efficient power delivery. The products in this guide use 16 AWG or 18 AWG conductors, with several described as pure or all copper. For a high-heat appliance, select a reputable cord that clearly states its gauge and conductor material rather than a listing that provides only a compatibility claim. The stated rating and gauge should work together.
In short, favor a clearly specified copper conductor with suitable AWG.
Cord Length and Routing
Length affects both convenience and countertop clutter. The shortest products measure 28.5 inches, while other choices are 3.28 feet, 4.56 feet, or five feet. A longer lead can make an outlet easier to reach, but the cord must still be routed so it cannot be pulled, snagged, exposed to grease, or placed where it contacts a hot surface. Choose a length that fits the counter without creating an avoidable trip or tension hazard.
In short, choose a practical length that reaches the outlet without hazardous slack.
Break-Away Safety Behavior
A magnetic fryer connection is intended to separate when pulled, which helps reduce the chance of dragging or tipping a hot appliance. That feature also means accidental contact can interrupt heating. The fryer should be placed on a stable surface and never moved while connected to power. If the magnetic plug separates, unplug the wall end before inspecting or reconnecting it, and check the magnetic pins for metal objects or debris.
In short, keep the fryer stationary and disconnect the wall plug before reattaching.
Heat and Wear Resistance
A fryer cord operates near a heat-producing appliance, so heat-resistant insulation and a durable outer jacket are important. Several listings specify a flame-retardant jacket, and one Presto option states resistance to temperatures up to 105°C. These claims do not mean the cord can touch oil, flames, or hot cookware without restriction. Route the lead away from the basket, burner area, hot housing, grease splatter, and pinch points, and replace it if the jacket cracks.
In short, select durable insulation but maintain proper separation from heat and grease.
Certification and Support
Independent certification provides a stronger specification reference than unsupported performance language. Several cords in the guide are ETL certified for 125V and 15A, while one listing also mentions an 18-month warranty and customer support. Certification does not establish compatibility, so it should be considered alongside the model list and connector measurements. Warranty and after-sales support can also be valuable when a replacement fails to match an accurately identified appliance.
In short, use certification as a quality reference, while separately verifying fit.
How to Use and Care for Your Deep Fryer Magnetic Power Cord Replacement
Before installation, unplug the fryer from the wall outlet and let the appliance cool completely. Identify the fryer model, compare it with the replacement’s compatibility list, and inspect both the fryer port and the magnetic connector. Clean the connector and remove any metal objects, crumbs, grease, or debris that could interfere with a secure magnetic connection.
Attach the magnetic plug to the fryer with the appliance in its normal operating position, then confirm that it is fully seated. Connect the other end to a suitable wall outlet only after the appliance is stable. Do not move the fryer while the cord is connected, and do not touch or pull the magnetic connection during operation. If it separates unexpectedly, disconnect the wall plug before reconnecting the appliance end.
For maintenance, wipe the outer cable and connector with a dry cloth after use and allow everything to cool before cleaning. Keep the cable away from hot surfaces, grease, and the basket, and never wrap it tightly around a hot fryer. Inspect for cracking, discoloration, damaged insulation, loose pins, or a connection that fails to remain seated, and replace the cord if any of these problems appear.
Frequently Asked Questions
Are all deep fryer magnetic power cords interchangeable?
No. Magnetic connectors can share a similar appearance while using different dimensions, pin counts, and electrical arrangements. Match the exact fryer model, connector geometry, voltage, amperage, and wire requirements before ordering. If the model number is unavailable, contact the seller or the fryer manufacturer rather than relying solely on how the connector looks.
How do I identify the correct Presto replacement cord?
Look for the model number on the fryer and compare it with the supported list. Many Presto replacements also reference 09982, 9982, or 85691, which can help identify the original part. Because several listings use similar 09982 language, check the voltage, connector design, and complete model number instead of choosing only by the part reference.
Can I use a 125V replacement cord for a 120V deep fryer?
A cord rated at 125V is commonly used with 120V household fryers because its rating is at least as high as the appliance’s operating requirement. The connector, amperage, wire gauge, and manufacturer specifications must still match. A higher cord rating does not make an otherwise incompatible connector fit or authorize use with a different electrical system.
Why does my magnetic fryer cord keep coming loose?
A break-away magnetic connection is designed to detach when pulled or disturbed, so it may separate if the cord is touched, snagged, or placed under tension. Check whether the fryer or cord is being moved, whether metal debris is on the magnetic pins, and whether the connector is fully seated. If it remains loose despite correct positioning and a clean connection, the cord may not be the right fit.
What should I do if the magnetic connection breaks while frying?
Do not reach toward the hot fryer or try to reconnect it while connected to the wall outlet. Switch off and unplug the wall end, allow the appliance to cool as appropriate, and then inspect the connector for metal objects, grease, or damage. Reconnect the cord only when both the fryer port and magnetic plug are clean, dry, and undamaged.
Is a 16 AWG cord better than an 18 AWG fryer cord?
A lower AWG number generally indicates a heavier conductor, but the correct choice depends on the fryer’s electrical specification and the cord’s overall rating. Some compatible 10L XL-style fryers are paired with 18 AWG cords, while other listed replacements use 16 AWG. Compatibility and certification matter more than comparing gauge numbers in isolation, and a cord should never be upsized without considering the appliance instructions.
Can a magnetic replacement cord extend the fryer’s reach?
A longer replacement can provide additional placement flexibility, but it should not be used to stretch the cord across a walkway or create tension at the connection. Five-foot and 4.56-foot options offer more reach than the 28.5-inch models. Route the lead behind the appliance, keep it away from hot and wet areas, and never use cord length to move a connected fryer.
How do I know if a replacement fryer cord is overheating or damaged?
Disconnect it from the wall and inspect the jacket for cracks, melting, discoloration, brittleness, or exposed conductors. Do not use the cord if the insulation is damaged, the magnetic pins are bent or loose, or the plug becomes unusually hot during operation. A damaged cord should be replaced with one that matches the fryer model and electrical specifications.
Final Thoughts on Choosing the Best Deep Fryer Magnetic Power Cord Replacement
The most versatile recommendation is the Deep Fryer Cord Compatible with Hamilton Beach & Masterbuild because it combines a 4.6 rating, ETL-certified 125V/15A construction, a 16 AWG pure copper cable, and a broad list of supported models. For a Presto appliance, the 09982 Magnetic Deep Fryer Power Cord offers a 4.5 rating, three original part-number references, and clear 120V/15A specifications. Masterbuilt owners can focus on the 9001150010 cord, which pairs a perfect 5.0 rating with a focused break-away design for the 10L XL models.
The most important buying priority remains exact compatibility. Confirm the full fryer model, connector dimensions, pin arrangement, voltage, amperage, and wire gauge before ordering. For many owners, a model-specific cord with a clear measurement list is easier to trust than a generic cable claiming broad compatibility. Whatever option is selected, route the cord carefully, keep it away from heat and grease, and never move a connected fryer.
Product listings, customer ratings, and prices can change, so check the current product page and updated customer feedback before making a final selection. Review the compatibility list against the appliance one more time, confirm that the replacement includes the expected magnetic connection, and select the cord that meets the fryer’s requirements rather than choosing on brand name or appearance alone.